Home      About      Contact      Submit an Item      
Passive    PV    Homes    Commercial    Wind    Projects    DIY    Resources    Tools    Materials    
Watch Twelve Essential Steps to Net Zero Energy

Twelve Essential Steps to Net Zero Energy Video


Watch Highline Park Design Thumbnail

Highline Park Design Video


Watch Highline Park NYC Thumbnail

Highline Park NYC Video


  

 

 

 

 

Our BatchGeo world MAP shows the locations of green architecture, green building and renewable energy projects featured on Solaripedia.

Project

SolarPump Charger Powers Portable Electronics

Credits: ©2011 Sol Design Lab

The SolarPump combines the adaptive reuse of an American car culture symbol (a 1950's Citgo gas pump) with an interactive system that harnesses solar energy to create a charging station for portable electronics and vehicles. The stand-alone mobile system can charge up to four electric bicycles and nearly unlimited laptops and cell phones, while LED lighting illuminates public seating crafted from recycled street signs. The system uses 195-Watt Sanyo PVs with a battery bank, that can also be grid-tied, with standard 110V outlets. Sol Design Lab, creator of the SolarPump, has designed and prototyped multiple solar-powered charging stations for use in urban areas, at festivals, business districts, campuses, and city transportation networks. Sol Design believes that as society transitions from gasoline cars to electric vehicles, solar charging stations will be crucial for providing the modern urban commuter with independent mobility. The company envisions that instead of a local gas station or convenience store, people will charge their electric bicycles and cell phones at solar-powered charging stations, while lounging in the shade of the solar roof on furniture made from recycled street signs and oil barrels. (Scroll to bottom for additional resources)

 

Solar Charging Station with Bike

Sol Design Lab in Austin, Texas, designs solar charging stations - using old gasoline pumps - to charge two to three electric bicycles, laptops or iPods, while providing LED lighting and public seating. ©2010 Sol Design Lab

Solar Pump Display Panel Design
By 4MS Studio
Sol Design Lab’s Solar Pump, a solar-powered charging station for mobile electronics, was an official part of South-by-Southwest (festival in Austin, Texas) this year. The stations have standard outlets, so anyone can walk up and charge a cell phone, laptop, or even an electric bike or scooter. The power comes from solar panels on the roof of the stations, so there’s no charge for charging (sorry… couldn’t resist). Refurbished 1950′s gas pumps provide a retro-future look that catches the public’s eye and twists the concept of “fill-up station.”

4MS Studio set up three stations throughout Austin, including a large station downtown by the convention center, a smaller “pump” outside the South Lamar Alamo theater, and a mobile “pump” at Auditorium Shores. The Solar Pump grew out of Beth Ferguson’s MFA project, and these represent the third generation of prototypes.

4MS Studio's main role was the design and construction of the digital display, which used LEDs to indicate solar panel voltage, power output (to the inverter) and battery bank voltage. More technical details below….

Each station is a little bit different, with either 2 or 4 deep cycle 100AH 12V batteries creating a 24V system. A 1100W inverter supplies standard 110VAC power to the user through a GFCI outlet (including a big red Emergency-Stop button!). Between 2 and 4 bi-facial Sanyo solar panels charge the batteries through a Morningstar charge controller. We used the Pentametrix system to read the shunts and voltages, and then send that data digitally over RS-232 to the custom digital display module. Click here for the Solarpump panel code.

Software
An Atmel AVR ATmega32A chip is at the core, communicating with the Pentametrix meter over a serial cable. The AVR makes a “request” to the Pentametrix every 500mS or so, and the Pentametrix responds with the latest readings: voltage on the solar panels, voltage on the battery bank, and current flowing out of the batteries to the inverter. The AVR then scales and converts these numbers and outputs them to the LED displays. The UART runs at 2400 baud, and the final byte is a checksum. If the checksum is off, or if the AVR doens’t hear a response from the Pentametrix, an error light goes on inside the box. Not terribly useful for debugging on the field, but on the bench this was handy.

Hardware
A Max232 chip handles the RS232 voltages, converting RS232 levels (-7V/+7V) to/from TTL levels (0V/5V). This directly connects to the AVR’s UART pins (RX/TX). These chips rule, they are totally worth the cost and board space.

Driving the LED displays turned out to be a little harder than I originally thought because the super-bright displays we found drop 7.4V, which is obviously higher than the 5V the AVR chip runs on. So I had to use an NPN/PNP transistor pair for each blue LED digit to switch +9V. (Q4/Q4B, Q5/Q5B, Q6/Q6B). This turned out to work well once I became OK with modifying the PCB and changing the code invert the “on” and “off” signals on the AVR pins for the blue digits only.

The yellow digits drop much less voltage, so I ran them on +5V and only needed on PNP transistor per digit (Q1, Q2, Q3). I’ve used the 2N5401 PNP transistor with good results for switching LED segments in other projects, and also have seen it around in the Peggy project… it’s fast and can drop a good amount of power… a keeper.

Finally, there’s a “bar graph” LED display which is 5 sets of LEDs, with 4 LEDs in parallel in each set. Each LED set is a different type of LED so they have a trimpot to set their brightness. I used the same 2N5401 PNP transistor on a 5V rail for these.

I went super-conservative on the powersupply, dropping the original 24V down to 18V, then to 9V, then to 5V.

Oh did I mention I found Pink LEDs! Yeah!!

Beth Ferguson (SolarPump's creator) and I drew up the front panel graphics in Illustrator, and I sheared some panels from 2mm aluminum. I then took that to a friend with a mill, who cut the rectangular holes for the numerical displays. I drilled out the round holes figured out a (perhaps excessively elaborate) way to mount the PCB to the front panel, and bend a flanged box to shield the circuit from the rear. The front panel is the main structural element and is mounted to braces which mount to the frame of the pump. I powdercoated the front panels white, and then applied the graphics with a decal, and baked that on. It came out pretty nice!


Documents

  Solar Charging Station Fact Sheet (2,840 kb)


Resources

Sol Design Lab (Texas, USA)